![]() It can be used to clean jewel holes after you’ve pre-cleaned them with a peg wood and to remove any excess lubrication. It’s highly absorbent, and it virtually leaves no residue behind. ![]() You can also use a peg wood to hold down a part (balance cock, pallet cock, etc.) while you’re unscrewing them or screwing them down. It works very well because the wood is hard enough to remove dirt but not that hard that it’ll damage the movement. The areas you should pre-clean are the jewel holes, bushes, the pallet stones, the crown of the pallets, and any areas that are caked with old hardened lubrication or dirt. Sharpen a peg wood and use it to pre-clean the parts before they go into the watch cleaning machine. You can either use manual handles or a hand fitting press.Ī set of A*F hand removing levers. In my opinion, the risk of damage is higher when you use a Presto puller tool but YMMV.Īfter the service, the hands need to be fitted again. I prefer a set of levers because I feel I have more control over the speed and the amount of pressure that is on the hands. This can be done with a Presto puller tool or a set of levers. Watch Hand Removing and Fitting Toolsīefore you can remove the dial and start working on the movement, you’ll need to remove the hands first. If it doesn’t work, you can use a press like this one. ![]() Most of the time, you can reinstall a snap-on case back with your thumbs. Use a case knife to apply force and create a slit to pop the case back off. The snap-on backs require a bit of practice because you want to cause as little damage to the case and case back as possible. If the back is very tight, I use a Jaxa tool. I like to use a “ sticky ball” to open screw-in backs if I can because it won’t damage the case at all. The two most used types of case backs are the “snap-on backs” and the “screw-in backs.” Watch Case Toolsīefore you can even begin to work on a movement, you’ll have to open the case first. Both loupes can be found on the same page.Īnother loupe (x10) is useful for inspecting jewel holes, balance staffs, etc. Using a headband, you can press the loupe against your eye while keeping both hands free to work on the watch. You’ll need a loupe to see the tiny parts you’re working on.Ī loupe with a medium magnification like x4 or x5 is sufficient for most work and can be worn at all times. The Bergeon 40 are very common universal movement holders.Įach is available in either steel or carbon fiber.Ģ Bergeon 4040 movement holders and a 4039 movement holder. Because parts of the machine protrude from it that could easily be damaged, such as the cannon pinion and sweep second pinion, it can’t be laid flat on the desk. In order to work on a movement, you need to secure it with a movement holder. They’re also antimagnetic.Ī brass pair of tweezers is helpful when you need to grab larger parts, such as bridges, or when you’re working on the mainspring or keyless works. You could use a #5 when working on the hairspring or shock protection system.īrass tweezers are great because they’re soft and won’t damage the movement. Therefore, it’s a good idea to invest in a high-quality antimagnetic tweezers such as a Dumont.Ī #2 or #3 tweezers work well for all-around use. Just like the screwdrivers, tweezers are essential because they’re your primary tools. The Bergeon 30081-S09 is my main set and the Beco set is dressed to be used with modern watches. I currently use the Bergeon 30081-S09 set and a Beco set with 9 screwdrivers and spare blades. I bought a 9-piece A*F carousel set and replaced the blades with Bergeon hardened steel ones. You don’t have to immediately invest in the most expensive set available. Screwdrivers and tweezers are essential tools for a watchmaker.īuy a good set that’ll last rather than a cheap one because a cheap set will break and damage your movement. You can always buy more tools when you gain more experience or when you need something specific (and you will). This list of tools will help you get started with watchmaking. What do you need, and do you need it right away? Maybe you’re considering watchmaking as a potential career choice.Įither way, you’ll need tools, but when you visit one of the wholesalers online, you’re overwhelmed with the huge variety of tools and equipment. Maybe you’re a watch collector and want to add to your hobby.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |